Wisdom in mind,   enthusiasm at heart.

NOS 11 (Release at 1st July)

Discrete  DAC + Headphone amplifier / Preamplifier
Combine from the NOS 7 + Master 9

Built in DSP data processor
Supports up to 768KHz
32bit / 384K Asynchronous Transfer  Amanero combo384
Built in 4 Pieces Hi-grade PCM1704UK Chips
9000mW at 40 ohm (Class A, per channels )
16000mW at 25 ohm (Max, per channels)
OCC wires and TCXO built in

The unit applied analog input short design :
          The unit  had design the analog idle input short circuit (  In 7 to In 9) for avoid the disturb between different sources.
         This design also applied in a lot high end brand devices.
          The working theory :  Without the idle input short circuit ,if the input 7 and input 8 had connect two extra DACs,  while users select the either input 7 and input 8 , the another input signal will fire through the circuits and mix  into the using signal, even though this signal is  weak  but still can degrade on the sound quality.
          With the idle input short circuit function : if user select either the input 7 and input 8, the another input signal will short circuit then no any signal fire through circuits , can keep the sound quality had not degrade.

Functions :
HP/PRE : For select the unit output from headphone sockets or the XLR / RCA sockets.
Selector : For select the unit input channels.
Volume: For change the volume of the unit.
DAC/PRE button: For select the unit as DAC output With volume control or Fixed level , without volume control output from the XLR / RCA sockets on rear .

The display auto dark :  Push into the jumper is auto dark .Please operate the jumper while the unit power off .

DSP-1 Jumpers setting

The product shipping before Oct. 12th. 2016

Jumpers Number

Setting

Functions describing

Jumper1  PLLEN

J1 (ON) ,J2(OFF) ：PLL1 active
J1 (OFF) ,J2(ON) : PLL 2 active
J1 (OFF),J2(OFF) :    All PLL off
J1(ON), J2(ON)    :    All PLL off

PLL 1 setting for both NOS modes

Jumper2  ATT0

PLL 2 setting for  NOS mode 1 only

Jumper4  IPS0

J4 (ON) : NOS mode 2

J4 (OFF) : NOS mode 1

NOS modes selection

Jumper5  IPS1

J5 (ON) :Smoother

J5 (OFF) : Neutral

Sound flavor selection

Jumper6  DITH

J6 (ON) :Asynchronous mode2  active

J6 (OFF) :Asynchronous mode1 active

Asynchronous  mode selection

The product shipping in or after Oct. 12th. 2016

Jumpers Number

Setting

Functions describing

Jumper1  PLLEN

J1(ON), J2(ON)    :    PLL1 active
J1 (ON) ,J2(OFF) ： PLL2 active
J1 (OFF) ,J2(ON) :    All PLL off
J1 (OFF),J2(OFF) :    All PLL off

PLL select for setting for all NOS modes

Jumper2  ATT0

Jumper3  ATT1

J3 (ON) :Smoother

J3 (OFF) : Neutral

Sound flavor selection

Jumper4  IPS0

J4 (ON),J5 (ON) : NOS mode 1
J4 (ON),J5 (OFF) : NOS mode 3
J4 (OFF),J5 (ON) : NOS mode 2
J4 (OFF),J5 (OFF) : NOS mode 1

NOS modes selection

Jumper5  IPS1

Jumper6  DITH

J6 (ON) :Asynchronous mode2  active

J6 (OFF) :Asynchronous mode1 active

Asynchronous  mode selection